Rear Compartment Wooden Panels

Discussions & announcements

Moderator: bobassel

Donovan
Posts: 221
Joined: Tue Dec 13, 2005 6:00 pm
Contact:

Rear Compartment Wooden Panels

Post by Donovan »

Everyone,

Happy New Year!!!

As I continue my restoration of the rear compartment on the GPA we are trying to figure out where the rear support ledge is situated on the inside rear wheel wells. In addition, whether there was support on the inside at the rear of the bulkhead or if the plywood just laid along the bulkhead at the location (as it is angling inward at that point).

The other question that I was interested in was how many wooden pieces there were in the rear compartment area? I have three that are nearly NOS condition but was not sure how many there actually was. I thought someone had actually drawn up some diagrams (Peter sent me one but when we looked at the dimensions we were not sure where it went). In addition, I can not seem to find the e-mail that referred to these wooden pieces. The manual does not have anything listed and no drawings of this area. Any help would be appreciated.

Thanks,

Donovan.
GPA 11374
acmack
Posts: 133
Joined: Wed Feb 08, 2006 1:31 am
Contact:

Re: Rear Compartment Wooden Panels

Post by acmack »

Does the photo in this G503 link help?
http://www.g503.com/forums/viewtopic.ph ... c&start=15

If not I can post more photos of my rear compartment as my wooden panels look to be complete and unaltered. David
GPA 9545
GPA 10568
1965 Apollo BP capsule A36
1960 Gemini BP capsule MSC 312
Donovan
Posts: 221
Joined: Tue Dec 13, 2005 6:00 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by Donovan »

David,

Thank you. The panel shown that is shown in your listing is one that I have but I am not sure of all the others. I have this one and the other side as well as one side of the piece that goes behind the gas tank. I understand there are ones that lie flat at the bottom of each of the two rear compartments (beneath the batteries)., but are there others?

Thanks,

Donovan.
GPA 11374
David Welch
Posts: 171
Joined: Thu Aug 03, 2006 10:23 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by David Welch »

Image
Image
Image
David Welch
GPW 77710
M29C 7195
Dukw 353-22096
Bantam trailer
GPA 1359
dmolasov
Posts: 25
Joined: Mon Sep 04, 2006 8:33 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by dmolasov »

We made some full-scale plans of the rear pressed board panels, which we made out of 1/4" MDF and had to tweak when we got down to final installation. I can share them with anyone who is interested, We generated the drawings from photos.
David Olasov
Brooklyn, NY

GPA 3936 (date of delivery 12/12/42)
Donovan
Posts: 221
Joined: Tue Dec 13, 2005 6:00 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by Donovan »

David,

I would like copies of your plans. Please send to mkdonovan@roadrunner.com

Thanks,

Donovan.
GPA 11374
leo verhagen
C-SICK
Posts: 260
Joined: Tue Dec 13, 2005 8:18 am
Contact:

Re: Rear Compartment Wooden Panels

Post by leo verhagen »

For me too please David, thanks!

fordgpa@zeelandnet.nl
Regards,

Leo Verhagen

http://communities.zeelandnet.nl/data/fordgpa/index.php

Ford GPA#8787 d.o.d. 27 Feb '43
Ford GPW#87243 d.o.d. 21 December '42
Willys MBT waiting for restoration
dmolasov
Posts: 25
Joined: Mon Sep 04, 2006 8:33 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by dmolasov »

Will do. It'll take me a couple of days to put them together. A design literate son and I digitized the shapes from a photo of the pieces that was taken from an angle. We got the shapes essentially correct. Bob Fulcher then sized them to the actual locations, make full size cartoons and sent them to me to cut the wood (we used 1/4" MDF, closer to the original stuff, at least the remaining original pieces on my particular vehicle, than plywood, in my view). I then cut them and returned them to Bob. He then fit them into the vehicle and sent them back to me for a further few adjustments. They are now installed on my vehicle, so Bob and I will have to figure out how to record the finished product, since when we were done, we hadn't anticipated a possible need to replicate our end product.

There was all this back and forth because the vehicle has been in Uxbridge, MA, 200 miles from my residence in Brooklyn and my woodworking equipment.

Regards
David Olasov
Brooklyn, NY

GPA 3936 (date of delivery 12/12/42)
acmack
Posts: 133
Joined: Wed Feb 08, 2006 1:31 am
Contact:

Re: Rear Compartment Wooden Panels

Post by acmack »

David, would you be willing to post the final "blueprints" here on G504 where we could all use them as a resource? Thanks for all your work in advance.
Where in Uxbridge is Bob located? I have 2 GPA's at my garage in nearby Rutland MA. David Ursin
GPA 9545
GPA 10568
1965 Apollo BP capsule A36
1960 Gemini BP capsule MSC 312
dmolasov
Posts: 25
Joined: Mon Sep 04, 2006 8:33 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by dmolasov »

Bob Fulcher has the full-scale templates we put together. We're trying to figure out what to do to make them available to everyone in a useful format.
David Olasov
Brooklyn, NY

GPA 3936 (date of delivery 12/12/42)
Cees
Posts: 194
Joined: Tue Dec 13, 2005 8:50 am
Contact:

Re: Rear Compartment Wooden Panels

Post by Cees »

Please can you make them in Autocad .dwg or .dxf Format that is easy to use for the cutting machine's.
Thanks
Cees
1941 Ford GP,
1943 Ford GPA #6849,
1943 Ford GPA # 7741,
1943 Harley WLC,
Dodge WC57,
1942 BMW R75,
1942 KS750,
1944 VW 166,
1940 Hanomag 20b,

http://www.filmprops.nl/produkten/fordgpa.htm
dmolasov
Posts: 25
Joined: Mon Sep 04, 2006 8:33 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by dmolasov »

My son Michael converted our original drawing, derived from a photo taken at an angle, into the formats Cees requested, and Bob sent me the full scale patterns that we marked up for one of the rounds of corrections. The second round fitted the boards into the vehicle, so there's no easy way to recapture those. But these corrected patters will definitely get you into the ball park. I'm sending the patterns on to Mike to get him to incorporate these changes into his digital drawings. Since he's on the West Coast these days, and I'm on the West, figure on another week to post these files or to let folks know that I have them. (I presume that making the changes won't be a big deal since Michael was able to convert the original file very quickly.
David Olasov
Brooklyn, NY

GPA 3936 (date of delivery 12/12/42)
Cees
Posts: 194
Joined: Tue Dec 13, 2005 8:50 am
Contact:

Re: Rear Compartment Wooden Panels

Post by Cees »

Dmolasov,

Any news on the drawings ??

Cees
1941 Ford GP,
1943 Ford GPA #6849,
1943 Ford GPA # 7741,
1943 Harley WLC,
Dodge WC57,
1942 BMW R75,
1942 KS750,
1944 VW 166,
1940 Hanomag 20b,

http://www.filmprops.nl/produkten/fordgpa.htm
dmolasov
Posts: 25
Joined: Mon Sep 04, 2006 8:33 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by dmolasov »

My son Michael finally did thke drawings, bukt he did them in pdf. I'm having him redraw them in the other formats that were requested. I don't know how to post them, but anyone interested can send me a private email and I'll send them on.
David Olasov
Brooklyn, NY

GPA 3936 (date of delivery 12/12/42)
jerome
Posts: 78
Joined: Mon Dec 12, 2005 10:21 pm
Contact:

Re: Rear Compartment Wooden Panels

Post by jerome »

Dear David

I sent you a PM, did you get it ? (it show sent in my profile but still in outbox!)

Thanks

Jerome
1939 BMW R12, 1941 GP, 1941 MB, 1942 MB, 1942 GPW, 1943 GPA, 1944 MB, 1945 Weasel M29C, 1950 JH101
http://www.jeepandmedic.com
Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests